AA3105-H14 White Color Coated Aluminum Coil for Gutters

AA3105-H14 White Color Coated Aluminum Coil for Gutters

AA3105-H14 white color coated aluminum coil is designed for rain gutter, downspout, fascia, soffit, flashing and roof drainage component production. The 3105 aluminum-manganese alloy combines useful strength, good formability, low weight and corrosion resistance with a factory-applied decorative and protective coating.

H14 is the primary temper for this product page and provides a practical balance of rigidity and roll-forming performance for suitable gutter and building-trim profiles. Other tempers such as H24, H26 and H28 can be discussed where a different combination of strength and forming performance is required.

PE, SMP, PVDF and project-specific coating systems are available according to outdoor exposure, color-retention requirements, fabrication method and budget. White finishes can be matched to RAL, PANTONE or an approved customer sample.

Request 3105-H14 Gutter Coil Pricing

Product Specifications

For roll-forming projects, provide the required temper, exact thickness and width tolerances, coil ID, maximum coil OD, coil weight, coating system, color, gloss level and finished gutter or downspout profile.

Send Your Gutter Coil Specification

Why AA3105 for Gutter and Downspout Production?

Good Roll-Forming Performance

AA3105 is widely used for roll-formed building products because suitable tempers provide the combination of rigidity and forming capability required for gutters, downspouts, fascia and other exterior profiles.

Higher Strength Than Commercially Pure Aluminum

The manganese-containing 3105 alloy provides greater mechanical strength than common commercially pure aluminum grades while retaining useful forming characteristics for building-product manufacturing.

Good Atmospheric Corrosion Resistance

AA3105 provides good general atmospheric corrosion resistance, while the factory-applied coating adds color and additional exterior surface protection. Actual service performance depends on coating condition, cut edges, fasteners, local environment and installation.

Lightweight Building Material

Aluminum has approximately one-third the density of conventional steel, helping reduce the weight of gutter and downspout components during handling, transportation and installation.

Compatible with Continuous Coil Coating

3105 aluminum can be supplied with factory-applied coating systems designed for continuous building-product fabrication, providing controlled color, gloss and surface appearance before roll forming.

H14 vs. H24, H26 and H28

Temper selection influences strength, hardness, bendability and roll-forming behavior. The same alloy should not be expected to have identical mechanical properties in H14, H24, H26 and H28 conditions.

For critical gutter profiles, the required temper should be established using the actual material thickness, bend radii, roll-forming sequence and finished mechanical requirements.

Product Picture

PE, SMP and PVDF Coating Options

PE Polyester Coating

PE polyester coating provides an economical factory-finished surface for gutter and building-trim applications where the selected coating specification satisfies the required outdoor exposure and appearance requirements.

SMP Coating

SMP coating can be specified for projects requiring a different balance of hardness, weathering performance and cost. Exact performance depends on the coating formulation and specified dry-film thickness.

PVDF Coating

PVDF is generally selected for more demanding exterior applications where long-term UV resistance, color retention and weathering performance are priorities. Final performance should be based on the approved coating specification rather than the PVDF name alone.

Custom White and Architectural Colors

White coating can be matched to a RAL, PANTONE or approved physical color sample. Other architectural colors can also be discussed for gutter systems that must coordinate with roofing, siding, fascia or facade finishes.

Key Advantages for Gutter Production

Roll-Forming and Fabrication Considerations

Gutter Machine Compatibility

Before ordering, confirm the required coil width, gauge, inner diameter, maximum outside diameter and coil weight accepted by the gutter or downspout forming machine.

Bending and Roll Forming

The allowable bend severity depends on temper, thickness, coating type and profile geometry. Tight or multiple bends should be validated with representative production material where coating integrity is critical.

Coating Protection During Forming

Roll-forming equipment should be clean, aligned and free from abrasive contamination. Tooling damage or trapped debris can scratch the finished white surface even when the coating itself has suitable adhesion.

Color Consistency

For large projects, distributors and repeat orders, approve a physical color sample and specify acceptable color and gloss tolerances. Ordering material for one project under the same approved coating specification helps control visual variation.

Discuss Your Roll-Forming Requirements

Product Display

Applications

Rain Gutters

AA3105 color coated aluminum coil can be roll-formed into suitable residential and commercial rain gutter profiles where the selected gauge, temper and width match the gutter machine.

Downspouts

The material can be fabricated into rectangular, round or project-specific downspout components according to the required profile and forming process.

Fascia and Soffit

Prepainted 3105 aluminum can be used for suitable fascia covers, soffit components and roof-edge finishing where the material specification meets the finished system requirements.

Roof and Wall Flashing

Color coated aluminum can be fabricated into flashing and trim for roof edges, wall transitions and other exterior water-management details when compatible with the adjoining materials and roof system.

Residential and Multi-Family Buildings

White gutters and downspouts can be coordinated with residential roofing, siding and facade colors for houses, villas, apartments and townhouses.

Commercial and Industrial Buildings

The coil can also be used for suitable drainage and exterior trim systems on offices, retail buildings, warehouses, workshops and other commercial or industrial facilities.

Coating Performance and Testing

Coating Thickness

The current product specification lists a 5-10μm primer and 15-25μm topcoat, with a total coating build of approximately 20-35μm. Final film build should be confirmed according to PE, SMP, PVDF or other approved coating system.

Coating Adhesion

Where coating adhesion is contractual, specify the required test method and acceptance criteria. Forming performance should also be evaluated after the relevant bend or roll-forming operation.

Salt-Spray Testing

Salt-spray duration by itself does not completely define real outdoor service life. If required, specify the test standard, exposure duration, scribe condition and acceptable blistering, corrosion or coating-creep criteria.

Accelerated Weathering

UV and accelerated-weathering requirements should identify the test cycle, duration and allowable color or gloss change. Performance should be matched to the selected coating system and intended climate.

T-Bend and Formability

For gutter and downspout production, coating flexibility can be evaluated using an agreed T-bend or production forming test to verify that the coating remains acceptable after bending.

Typical Production and Quality-Control Flow

1. Aluminum Substrate Verification

The incoming 3105 substrate is checked against the required alloy, temper, thickness and dimensional specification.

2. Surface Pretreatment

The aluminum surface is cleaned and prepared to support coating adhesion and exterior corrosion performance.

3. Primer and Topcoat Application

The specified coating system is applied using controlled coil-coating processes according to required color, gloss and dry-film build.

4. Controlled Curing

The applied coating is cured according to the coating-system requirements to develop the required adhesion and surface properties.

5. Slitting and Rewinding

Wide coated coil can be slit and rewound to the width, coil weight and winding configuration required by the customer's gutter or downspout production equipment.

6. Final Inspection

Inspection can include dimensions, coating thickness, color, gloss, surface appearance, adhesion and other agreed properties before packaging.

How to Specify 3105-H14 Gutter Coil

Confirm H14 or Another Required Temper

This page is based on AA3105-H14. If the gutter machine or existing specification requires H24, H26, H28 or another temper, identify it explicitly in the inquiry.

Provide Exact Thickness and Width

Provide nominal thickness, thickness tolerance, width and width tolerance. Standard building-product or gutter-machine widths can also be supplied where they fall within the available production range.

Select the Coating System

Specify PE, SMP, PVDF or another required system according to exterior exposure, required color retention and applicable project requirements.

Specify the White Color

Provide a RAL, PANTONE, existing paint code or physical color sample. Also identify the required gloss level and acceptable color tolerance where appearance matching is important.

Provide Coil Configuration

Specify coil inner diameter, maximum outer diameter, target coil weight, winding direction and any packaging limits imposed by the customer's material-handling equipment.

Provide the Finished Gutter Profile

A finished profile drawing or gutter-machine specification helps confirm the required width, bend severity and material condition before commercial production.

Specify Required Tests and Documentation

Where required, state the applicable material standard, coating thickness, adhesion, T-bend, salt spray, accelerated weathering, color, gloss and inspection-document requirements in the purchase specification.

Export Packaging

Coils can be packed with moisture-resistant wrapping, protective edge materials and export pallets according to coil size and transportation requirements. Horizontal or vertical packing can be discussed according to handling and unloading conditions.

Final packing should protect the coated surface and coil edges against moisture, scratching, collision and deformation during inland handling and international transportation.

Frequently Asked Questions

Why is AA3105 suitable for rain gutters and downspouts?

AA3105 combines useful strength, good roll-forming capability, relatively low weight and good atmospheric corrosion resistance, making suitable tempers widely applicable to gutters, downspouts and other exterior building products.

Is this product H14 or H24?

This product page is based on AA3105-H14. H24, H26, H28 and other conditions can be discussed separately where the customer's forming or mechanical requirements call for a different temper.

What is the difference between 3105-H14 and 3105-H24?

Both are non-heat-treatable 3105 aluminum conditions, but they achieve their properties through different strain-hardening and annealing routes. Their mechanical and forming performance should be compared using the applicable standard, thickness and finished profile requirements.

Can AA3105-H14 be roll-formed into gutters?

Yes, suitable AA3105-H14 coil can be used for roll-formed building products. Compatibility should be confirmed with the actual gauge, width, gutter-machine design and finished profile.

What thickness range is available?

The current listed range is 0.3mm to 1.2mm, subject to temper, width, coating system and production confirmation.

What width range is available?

The current listed range is 800mm to 1600mm, with 1000mm, 1220mm and 1500mm listed as standard widths. Custom slitting requirements should be confirmed with the inquiry.

Can narrow gutter coil widths be supplied?

Custom slit widths can be discussed from suitable master coils. Provide the exact gutter-machine width, tolerance, coil ID and target roll weight for confirmation.

Which coating is best for outdoor gutters?

The appropriate coating depends on climate, UV exposure, required appearance retention and budget. PVDF is generally selected for more demanding long-term exterior exposure, while PE and SMP systems can be suitable where their specified performance meets the project requirements.

Can the coating be customized in white?

Yes. White can be matched to a RAL, PANTONE or approved physical color sample. Specify gloss and acceptable color variation where exact matching is important.

Are other colors available?

Yes. Custom architectural colors can be discussed according to coating system, color reference, order quantity and production requirements.

Can matte and glossy finishes be supplied?

Yes. Matte, semi-gloss and glossy finishes are available according to the approved coating specification.

Can the coating withstand gutter roll forming without cracking?

A suitable coating and temper can provide good forming performance, but coating integrity depends on bend severity, substrate condition, film build and roll-forming setup. Critical profiles should be validated using an agreed bend or production test.

Does a 1000-hour salt-spray result guarantee outdoor service life?

No. Accelerated salt-spray testing is a controlled laboratory evaluation and does not directly translate into a specific number of outdoor service years. Test method and acceptance criteria should be specified separately.

Can the material be used for fascia and soffit?

Yes. Suitable 3105 color coated coil can be used for fascia, soffit and related exterior building trim when the gauge, temper, coating and profile meet the finished product requirements.

Can it be used for roof flashing?

Yes. Prepainted 3105 aluminum can be fabricated into suitable flashing profiles where material compatibility, thickness and installation details meet the roof-system requirements.

Which standards can be specified?

Material can be ordered according to an agreed ASTM, EN, GB/T or other applicable specification. Identify the exact required standard and inspection documents before production.

What is the delivery time?

The original product information lists approximately 7-10 working days for standard specifications and 12-15 working days for customized products. Final lead time should be confirmed against quantity, coating, color, production schedule and shipping requirements.

What information should I provide for a quotation?

Please provide AA3105-H14 or required alternative temper, thickness, width, coil ID, maximum coil OD, coil weight, PE/SMP/PVDF coating, coating thickness, white color reference, gloss, gutter or downspout profile, forming-machine requirements, quantity, test standards, required inspection documents and delivery destination.

Request a Quote for AA3105-H14 White Gutter Coil

If you are sourcing AA3105-H14 white color coated aluminum coil for rain gutters, downspouts, fascia, soffit or roof drainage products, send us your thickness, width, coil configuration, coating, color and forming requirements for specification confirmation and quotation.

Contact Us for Pricing