Laminate
Dingang
| Availability: | |
|---|---|
| Quantity: | |
Multi-layer high-barrier aluminum composite film combines solid aluminum foil with functional polymer layers such as PET, PA Nylon, PE and CPP to create flexible barrier materials for industrial packaging, FIBC liners, export protection, moisture-sensitive equipment, selected electronics packaging and other demanding applications.
The aluminum foil layer provides the primary barrier against water vapor, oxygen and light when it remains intact. Outer PET or PA layers provide mechanical reinforcement and printing support, while PE, CPP or another application-specific inner layer provides heat sealing and product-contact compatibility.
Typical structures include PET/AL/PE, PET/AL/CPP, PA/AL/PE and PET/AL/PA/PE. Total thickness, aluminum foil gauge, polymer layers, sealing surface, printing, roll dimensions and mechanical reinforcement can be adjusted according to the packed product and converting process.
Industrial barrier requirements should be specified for the complete laminate or finished bag. Foil thickness alone does not determine package performance because folds, punctures, flex cracking, heat seals, closures, internal humidity and chemical compatibility can affect the finished barrier system.
Request Barrier Film Samples and Pricing
| Parameter | Available / Current Range | Application Guidance |
|---|---|---|
| Product Type | Multi-Layer Aluminum Foil Barrier Laminate | For flexible and industrial protective packaging |
| Standard Structure | PET / AL / PE | General high-barrier pouches, liners and industrial protection |
| Alternative Structure | PET / AL / CPP | Where a compatible PP-based sealant is required |
| Reinforced Structure | PA / AL / PE | Higher puncture and flex resistance |
| Heavy-Duty Structure | PET / AL / PA / PE | FIBC liners, bulk packaging and mechanically demanding industrial applications |
| Total Thickness | 50–250 μm | Select according to bag size, load, handling and mechanical requirements |
| Aluminum Foil Thickness | 6–15 μm | Select according to barrier, pinhole and flex requirements |
| Maximum Width | Up to 2000 mm | Suitable for wide industrial liners and rollstock subject to production feasibility |
| Outer Film | PET / PA / Custom | Provides mechanical protection, printability or puncture resistance |
| Inner Sealant | PE / LLDPE / CPP / Application-Specific | Must be compatible with the packed product and sealing process |
| Surface Finish | Glossy / Matte | According to printing, handling and appearance requirements |
| Printing | Gravure Printing Available | For branding, handling instructions, hazard information and technical markings |
| OTR | Project-Specific Finished-Laminate Target | State exact test method, temperature and humidity |
| WVTR / MVTR | Project-Specific Finished-Laminate Target | Specify exact test conditions for moisture-sensitive applications |
| Heat-Seal Strength | Application-Specific | Define seal temperature, pressure, dwell time and test method |
| Puncture Resistance | Structure-Specific | PA reinforcement can be introduced for sharp or heavy products |
| Antistatic / ESD Performance | Optional Dedicated Structure | Standard PET/AL/PE should not automatically be treated as an ESD shielding bag |
| VCI Function | Optional Dedicated Structure | Use where corrosion-inhibiting chemistry is required for suitable metal products |
| Supply Form | Rollstock / Bag / Liner / Sheet / Custom Cover | Configure according to packing equipment and end-use dimensions |
Send Your Barrier Packaging Specification
PET provides dimensional stability, tensile strength and a durable outer surface for printing and handling. It also protects the mechanically sensitive aluminum foil from direct abrasion.
Solid aluminum foil provides the principal barrier against water vapor, oxygen and light when the foil remains continuous and undamaged.
PA Nylon can improve puncture resistance, tear toughness and flex durability for heavy-duty liners, irregular industrial components and products with harder edges.
PE provides heat sealing, flexibility and the internal contact surface for many industrial packaging applications. The exact PE formulation should be selected according to sealing conditions and product compatibility.
PET/AL/PE is a practical three-layer construction for equipment parts, powders, ingredients and other products that need strong moisture, oxygen and light protection without extreme puncture loads.
PET supports handling and printing, aluminum provides the barrier, and PE provides the sealing surface.
Finished laminate thickness should be selected from package size, product weight, folding geometry and transport conditions rather than from barrier requirements alone.
FIBC liners and bulk barrier bags can experience greater mechanical loads during filling, lifting, transportation and discharge. PET/AL/PA/PE structures introduce a Nylon reinforcement layer to improve toughness and puncture resistance.
Barrier liners can be used inside compatible FIBCs for powders, resins, minerals, ingredients and other bulk materials where external moisture or oxygen exposure must be reduced.
Industrial liners can be fabricated with filling spouts, discharge spouts or custom openings according to FIBC geometry and handling requirements.
Suitable liners can be designed for vacuum evacuation or controlled gas flushing where the sealing construction and liner strength are validated for the process.
Wide liners and bulk bags require consistent seals because a small channel leak can compromise the barrier of the entire package.
High-barrier aluminum laminates can be converted into large bags, equipment covers, pallet covers and crate liners for machinery, metal components and moisture-sensitive assemblies during ocean freight or long-term storage.
The barrier laminate limits the entry of external moisture-laden air while an appropriately sized desiccant can absorb moisture trapped inside the sealed package.
Desiccant quantity should be selected from package volume, initial internal moisture, expected storage period and environmental exposure rather than added without calculation.
Vacuum packaging can reduce the volume of trapped humid air and improve package compactness for suitable industrial products, but sharp equipment edges must be isolated or reinforced to prevent punctures.
Rollstock can be converted into three-dimensional covers for machinery, equipment and palletized loads where standard flat bags are impractical.
Aluminum barrier film reduces ingress of external moisture and oxygen but does not itself guarantee that a metal component will remain corrosion-free.
Corrosion protection depends on the metal type, cleanliness, residual salts, humidity inside the package, storage duration, temperature cycling and barrier integrity.
Barrier bag plus desiccant is appropriate where humidity control is the primary corrosion-management strategy.
VCI functionality requires a specifically formulated corrosion-inhibiting layer or compatible VCI source. Standard PET/AL/PE laminate should not automatically be described as VCI packaging.
Where military or defense packaging requires a specification such as MIL-PRF-131 or a bag qualification under MIL-DTL-117, the exact qualified material and converted package should be specified. A generic commercial foil laminate should not be represented as compliant without the required documentation.
Electronics packaging can require both a very low moisture transmission rate and electrostatic-discharge protection. These are separate functions.
A conventional PET/AL/PE industrial barrier bag can provide excellent moisture protection but should not automatically be used as a moisture-barrier ESD shielding bag for sensitive semiconductor devices.
For electrostatic-discharge susceptible devices, packaging should meet the required ESD protective properties specified by the applicable ESD control program.
Moisture-sensitive semiconductor devices can require dedicated dry-pack procedures including a qualified moisture-barrier bag, desiccant, humidity indicator and appropriate sealing and labeling.
Dedicated ESD moisture-barrier bags can require controlled surface resistance on the inner and outer surfaces together with static-shielding performance.
Trays, reels and electronic assemblies can have sharp edges, making nylon reinforcement useful for preserving bag integrity and barrier performance.
| Requirement | General Foil Barrier Film | Dedicated Electronics MBB |
|---|---|---|
| Moisture Barrier | Yes, according to structure and test result | Yes, with electronics-specific MVTR requirements |
| Oxygen Barrier | High | May be high but is not the only required function |
| Static Dissipation | Not automatic | Specified and tested |
| Static Shielding | Not automatically qualified | Specified where required for ESDS devices |
| J-STD-033 Dry Pack | Not automatically compliant | Can be designed for applicable dry-pack requirements |
A generic PET/AL/PE or PET/AL/PA/PE industrial laminate should not automatically be described as lithium-ion battery pouch film.
Battery pouch materials use specially engineered aluminum-plastic laminate constructions with controlled aluminum thickness, high formability, electrolyte resistance, inner CPP-type sealing layers and surface treatment designed for the electrochemical environment.
Buyers requiring battery pouch material should specify it as a dedicated battery-grade laminate rather than selecting a standard industrial barrier film only by total thickness or aluminum content.
Aluminum foil laminate can be used for selected chemical powders, resins and industrial raw materials where moisture, oxygen or light protection is required.
Chemical resistance must be evaluated against the complete structure. Aluminum foil does not make PE, CPP, PA, PET or the laminating adhesive universally resistant to aggressive chemicals.
Strong acids and alkaline materials can require specialized inner liners or alternative materials. Product compatibility should be tested before commercial use.
Solvents can swell, soften or permeate conventional polymer sealant layers and may also affect adhesive bond strength.
Reactive, oxidizing or otherwise hazardous chemicals require a full packaging-compatibility and regulatory review beyond ordinary barrier-film selection.
Suitable aluminum foil laminates can also be used for dry ingredients, powders, agricultural products and other foods requiring a strong moisture, oxygen and light barrier.
Food-contact suitability must be confirmed for the exact inner sealant, adhesive, ink, coating, packed food and conditions of use. Industrial packaging material should not automatically be presented as food-contact compliant without the supporting structure-specific documentation.
Moisture-sensitive powders can benefit from foil liners where water-vapor ingress would cause caking, clumping or product degradation.
High-barrier liners can be considered for seeds and other agricultural products where oxygen, moisture and light exposure need to be controlled according to the storage program.
General industrial PET/AL/PE laminate should not be confused with pharmaceutical blister materials.
Suitable aluminum-containing flexible laminates can be developed for pharmaceutical sachets when the product-contact, sealing, migration and regulatory requirements are specifically defined.
Conventional push-through blister lidding commonly uses hard pharmaceutical aluminum foil with a heat-seal lacquer and is fundamentally different from a general flexible industrial laminate.
Cold-form blister material commonly uses a dedicated multilayer structure such as OPA / aluminum / PVC, with a much thicker soft aluminum layer selected for cavity forming.
Aluminum composite films can be used as facing or vapor-control layers in selected insulation and technical building products.
The aluminum laminate itself should not be described as thermal insulation solely because it contains reflective foil. Thermal resistance is primarily provided by the insulation layer and the complete assembly.
Continuous foil facings can provide very low vapor permeability, but seams, penetrations, joints and installation details determine the vapor-control performance of the finished assembly.
Reflective aluminum surfaces can reduce radiant heat transfer when installed facing an appropriate air space. A foil surface sandwiched tightly between solid layers does not provide the same radiant-barrier effect.
Numerical OTR requirements should be specified for the finished laminate using an agreed test method and environmental conditions.
ASTM D3985 is one recognized method for oxygen-transmission testing of suitable flexible packaging materials.
ASTM F1249 can be used for suitable flexible structures where quantitative water-vapor transmission is required.
Test temperature and relative humidity must be reported with WVTR or MVTR values because measurements performed under different conditions are not directly interchangeable.
Film barrier values do not automatically define finished-bag barrier performance. Seams, closures, spouts, valves, folds, pinholes and punctures can create additional transmission paths.
Thin aluminum foil is an excellent barrier but has limited elongation compared with flexible polymer films.
Severe folding, repeated flexing, tight gussets or sharp product edges can create microcracks in the foil and reduce moisture and oxygen protection.
Increasing foil gauge can reduce pinhole risk and improve robustness in some structures, but it can also affect flexibility, cost and converting behavior.
PA can reinforce the laminate and absorb mechanical strain, particularly where packages are vacuumed, folded repeatedly or loaded with hard products.
For critical applications, OTR or WVTR can be evaluated after representative flex or handling tests rather than only on untouched flat film.
Industrial barrier packaging relies on properly formed seals to maintain a closed protective environment.
Seal strength should be specified together with the actual PE or CPP inner layer, sealing temperature, pressure and dwell time.
ASTM F88/F88M can be used where appropriate to quantify seal strength of flexible barrier materials.
Large machinery covers and FIBC liners require consistent temperature and pressure along long sealing jaws. Field sealing equipment should therefore be validated using the actual laminate thickness.
Dust, powder or product particles in the sealing area can create channels. Filling systems should minimize seal contamination or use a sealant and process validated under representative conditions.
Delamination between PET, PA, aluminum and PE layers can compromise mechanical durability and can expose the thin foil to damage.
Aluminum and polymer surfaces must be sufficiently clean and prepared for the selected adhesive system.
Reactive laminating adhesives require adequate cure before demanding converting, bag making or product exposure.
Oils, solvents or chemicals can affect adhesive bond strength. The laminate should be tested with the actual packed product where interaction is possible.
| Property | Solid Aluminum Foil Laminate | Metallized Film |
|---|---|---|
| Metal Layer | Continuous aluminum foil | Very thin deposited metallic layer |
| Light Barrier | Complete opacity when foil remains intact | Depends on metallization and film construction |
| Moisture / Oxygen Barrier | Very high | Can be high but generally lower and more structure-dependent |
| Flex Sensitivity | Foil can crack under severe repeated flexing | Often more flexible, but deposited layer can also be damaged |
| Selection | For applications prioritizing maximum barrier | For applications balancing barrier, flex, weight and cost |
Gravure printing can be supplied for branded packaging, batch identification, product information, handling instructions, warning symbols and technical markings.
Where transparent PET is used as the outer layer, reverse printing can protect the ink inside the laminate from abrasion during shipping and handling.
Industrial and electronic packaging can include lot codes, manufacturing information and traceability markings according to the customer's quality system.
| Inspection Item | Purpose | Control Direction |
|---|---|---|
| Layer Structure | Confirms the ordered laminate construction | Verify polymer type, foil and sealing layer |
| Total Thickness | Controls mechanical and converting behavior | Specify nominal gauge and tolerance |
| Aluminum Foil Gauge | Influences barrier and pinhole performance | Measure foil separately from total laminate thickness |
| Pinhole Inspection | Screens foil continuity | Define acceptance criteria where high barrier is critical |
| Lamination Bond | Reduces layer separation | Evaluate after adhesive cure |
| OTR | Quantifies oxygen barrier | ASTM D3985 or agreed method and conditions |
| WVTR / MVTR | Quantifies moisture barrier | ASTM F1249 or agreed method and conditions |
| Seal Strength | Controls bag and liner integrity | ASTM F88/F88M or agreed method |
| Puncture Resistance | Important for industrial parts and FIBC liners | Set application-specific minimum performance |
| Tensile / Tear Strength | Supports handling and bag conversion | Specify where heavy loads are involved |
| Flex Durability | Screens foil cracking during use | Evaluate barrier after flexing where required |
| Chemical Compatibility | Prevents sealant or adhesive failure | Test with actual industrial product |
| ESD Surface Resistance | Required for dedicated ESD packaging | Specify applicable electronics packaging standard |
| Static Shielding | Protects ESDS products from discharge events | Test only for dedicated shielding structures |
| Roll Width | Supports converting-line compatibility | Specify slit tolerance and edge condition |
| Winding Quality | Supports stable unwinding | Inspect telescoping, wrinkles and edge damage |
Barrier-film rollstock should be protected from moisture, impact, edge damage, telescoping and contamination during storage and international transportation.
Depending on roll dimensions and finished format, packaging can include wooden cases, palletized coils, moisture-resistant wrapping and customized protection for export shipment.
Wooden Case Packing
Pallet Coil Packing
Aluminum Foil Barrier Bag
For accurate structure selection and pricing, please provide:
Packed product or equipment
Industrial, FIBC, electronics, food, pharmaceutical sachet or other application
Required package format: roll, pouch, liner, cover or sheet
Preferred PET/AL/PE, PA/AL/PE, PET/AL/PA/PE or other structure
Required total thickness
Required aluminum foil gauge
Required width
Package dimensions and load weight
Sharp edges or puncture-risk conditions
Required OTR and test conditions
Required WVTR or MVTR and test conditions
Required seal strength
Sealing-machine type and sealing conditions
Vacuum packaging requirement
Gas-flushing requirement
Desiccant system if used
VCI requirement if used
Chemical compatibility requirements
ESD surface resistance and shielding requirements if applicable
J-STD-033 dry-pack requirement if applicable
MIL-PRF or MIL-DTL requirements if applicable
FIBC filling and discharge spout dimensions if applicable
Printing artwork or technical markings
Roll core ID, maximum OD and roll weight
Order quantity
Destination port or delivery location
Get a Custom Industrial Barrier Film Proposal
It is a flexible laminate combining solid aluminum foil with polymer layers such as PET, PA, PE or CPP to provide barrier, mechanical reinforcement and heat-sealing functions.
PET/AL/PE is suitable for many general high-barrier pouches, liners and industrial packaging applications requiring strong moisture, oxygen and light protection.
PA improves toughness, puncture resistance and flex durability and is useful in heavy-duty liners, vacuum packaging and packages containing hard or irregular products.
The current total laminate range is approximately 50–250μm, with final thickness selected according to structure and application.
The current aluminum foil range is approximately 6–15μm for this product family.
Yes, widths up to approximately 2000mm are within the current product direction, subject to the laminate structure and production feasibility.
Yes. PET/AL/PA/PE and related reinforced structures can be developed for FIBC liners where high barrier and greater mechanical durability are required.
Suitable liner structures can be designed for vacuum processes when seal strength, puncture resistance and the complete bag geometry have been validated.
Yes. Barrier bags or covers can reduce external moisture ingress. Desiccants or a compatible VCI system may also be required depending on the metal, storage period and environment.
No. Corrosion also depends on internal moisture, salts, contamination, metal type, temperature, handling and package integrity.
No. VCI protection requires a specifically formulated corrosion-inhibiting system or compatible VCI source.
Military-specification projects require the exact qualified material and converted packaging construction. Compliance should only be claimed when supported by the applicable qualification and documentation.
A suitable foil laminate can provide excellent moisture protection, but ESD-sensitive electronic components normally require dedicated electrical surface-resistance and static-shielding properties.
Not automatically. ESD packaging requires specifically engineered and tested electrostatic properties in addition to moisture barrier.
ANSI/ESD S541 defines ESD protective packaging properties, while IEC 61340-5-3 provides technically equivalent requirements for packaging intended for electrostatic-discharge sensitive devices.
IPC/JEDEC J-STD-033 addresses handling, packing, shipping and use of moisture- and reflow-sensitive electronic devices, including dry-packing requirements.
It should not be assumed suitable. Lithium-ion pouch cells require a specialized aluminum-plastic laminate designed for deep forming, electrolyte resistance and battery sealing performance.
It can be used for selected chemicals and industrial powders after compatibility testing. Standard PE, CPP, PET, PA and adhesives are not universally resistant to all chemicals.
Only after specific compatibility evaluation. Aggressive acids, bases and organic solvents can attack polymer sealants or adhesive layers even when the aluminum barrier itself remains present.
Suitable structures can be developed for pharmaceutical sachets, but pharmaceutical blister lidding and cold-form Alu-Alu packaging use dedicated structures and specifications.
No. Cold-form blister material commonly uses a dedicated OPA/aluminum/PVC construction with a much thicker soft aluminum layer designed for cavity forming.
It can be used as a facing or vapor-control layer in suitable insulation assemblies, but the film itself should not be treated as the primary thermal insulation.
Reflective radiant-barrier performance generally requires the reflective surface to face an appropriate air space. Foil tightly sandwiched between solid layers does not provide the same radiant effect.
State the maximum transmission value together with the exact laminate, test method, temperature and relative humidity.
Yes. Severe folds and repeated flexing can create microcracks in thin aluminum foil and reduce the effective barrier.
Not automatically. Thicker foil can improve robustness and reduce pinhole risk but can also change flexibility, cost and converting behavior.
Yes. Custom gravure printing can be provided for branding, instructions, technical information and warning marks according to the approved artwork.
Please provide the packaged product, application, required structure, total thickness, foil gauge, width, package dimensions, OTR and WVTR targets, puncture and seal requirements, ESD or VCI functions, printing, quantity and destination.
Yes. New industrial packaging structures should be tested with the actual product, bag geometry, sealing equipment, storage environment and transportation conditions before commercial production.
Products
Application
Quick links
Contact Us